Shop our Store

Shop by Manufacturer

Get Discounts and
StangSuspension News
Sent to your Email

  Home > K-Members >

  Maximum Motorsports Front K-Member - For 96-04 Mustangs w/ 4.6L Engine (w/ Hellion Turbo Kit)
Maximum Motorsports Front K-Member - For 96-04 Mustangs w/ 4.6L Engine (w/ Hellion Turbo Kit)


 
Market Price $679.00
Sale Price $649.95



Availability: Usually Ships in 24 Hours
Product Code: 1698
Qty:

Add to Wishlist
Product Details
 
Product Details
  • Maximum Motorsports spent over two years optimizing this K-Member, both on the track and on the computer. The result is that the front of your car will corner like nothing else you've experienced. Unlike other K-Members on the market, strength, stiffness, and durability are given a higher priority than ultra-low weight so that your investment will last the life of your vehicle.

    What makes the Maximum Motorsports K-Member Different:
  • MM's K-Member lengthens the wheelbase 3/4", which improves the front/rear weight distribution and increases caster.
  • MM optimized the vertical location of the control arm pivots. This improves the camber curve on lowered vehicles and improves the roll center height.
  • MM's K-Member offers two different vertical locations for the control arm pivots, allowing you to choose the one that's best for your car's ride height.
  • MM optimized the location of the steering rack for the greatest improvement in Ackerman steering geometry, which helps reduce understeer and tire wear.
  • After extensive testing of anti-dive, MM determined that Ford got it right! The stock amount of anti-dive is best, and that is what we built into our K-member.
  • MM's K-Member allows 5.0 engines to be set back one inch.
  • The MM K-Members are modular, allowing 5.0 engines to be installed in 96+ cars, or modular engines to be installed in pre-96 cars.
  • Increased oil-pan clearance for all aftermarket oil-pans means oil-pan service is easier.
    Header clearance is increased by over 1" in critical areas.
  • Easier access to the starter motor.
  • Pre drilled plumb bob holes for easy and accurate squaring of the K-member to the car.
  • The factory Ford K-Members weigh on average 50lb. The MM K-Member weighs 36lb.

    In addition to the K-Member, you will also need the following:
  • Tubular front control arms (stock control arms are not compatible because of the large outside diameter of the pivot bushings)
  • Caster/Camber plates
  • Front Coil-Over conversion kit
  • Aluminum steering rack bushings
  • Adjustable Tie-Rod Ends (bumpsteer kit)
  • If using on 4V Cobra Engine, you must also use an oil filter relocation kit which is also on our website.

    Note - This K-Member is designed to work with 4.6L Mustangs with the Hellion Turbo Kit Installed. It is specially designed for the Turbo Piping. Non Hellion Turbo Mustangs will use part # MMKM-2

    Fits 1996-2004 Mustang 4.6L V8 with Hellion Turbo Kit Installed

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

K-Members
Maximum Motorsports


MM Coil-Over Complete Package - For 79-89 Mustangs
MM Coil-Over Complete Package - For 99-04 Cobra
Maximum Motorsports Rear Coil-Over Kit and Hypercoil Spring Package - For 87-04 Mustangs with Koni Shocks
MM Rear Coil-Over Kit and Hypercoil Spring Package - For 87-04 Mustangs with Bilstein Shocks
MM Coil-Over Complete Package - For 79-89 Mustangs
MM Coil-Over Complete Package - For 99-04 Cobra
Maximum Motorsports Rear Coil-Over Kit and Hypercoil Spring Package - For 87-04 Mustangs with Koni Shocks
MM Rear Coil-Over Kit and Hypercoil Spring Package - For 87-04 Mustangs with Bilstein Shocks
$1,599.95
$1,599.95
$449.95
$449.95